My Account

Wish List (0)

PiBorg

PiBorg

Written by in Diablo - Build on

The Diablo motor controller is a dual channel 55A motor controller capable of powering large motors with power supplies up to 36V. In this guide, we'll go through how to: Getting to know your Diablo Connect the Diablo to a Raspberry Pi Connect the Diablo to a power supply and motor How to enable I2C on the Raspberry Pi How to install the Diablo libraries and...

0 Comments

Written by in Diablo - Build on

In this example, we'll go through how to: Connect the Diablo to a Raspberry Pi Connect the Diablo to a power supply Connect the Diablo to two motors How to enable I2C on the Raspberry Pi How to install the Diablo libraries and use the sequence example Parts you will need One Diablo board with I2C connecting cables A Raspberry Pi 3B+ A...

0 Comments

Written by in Diablo - Build on

In this example, we'll go through how to: Connect the Diablo to a Raspberry Pi Connect the Diablo to a power supply Connect the Diablo to a 4 wire stepper using a multimeter How to enable I2C on the Raspberry Pi How to install the Diablo libraries and use the stepper example Parts you will need One Diablo board with I2C connecting cables.

0 Comments

Written by on

Our latest board is here, the TroPi! Add a bar of LEDs to your Raspberry Pi to make it glow or take the TroPi and build it into your very own trophy.

0 Comments

Written by on

Using a Raspberry Pi, a PiBorg ZeroBorg and inspiration from new micro-organisms, artists Anna Dumitriu and Alex May have created ArchaeaBot, an underwater life form which is touring the UK and Europe.

0 Comments

Written by in Build, TroPi - Build on

Use the trophy lid kit and a TroPi to build your very own trophy using the Raspberry Pi.

0 Comments

Written by in Build, TroPi - Build on

Getting started guide for the TroPi add on board, add LEDs to your project.

0 Comments

Written by on

Wow! What a weekend it has been! Massive thank you shoutout to Michael Horne and Tim Richardson for putting together what has been an absolutely fantastically organised weekend! Being my first ever Pi Wars, and not really understanding anything technically (at least not yet!) it was great to start engaging in the community, though. I met so...

0 Comments

Written by in Build, DiddyBorg V2 - Build on

To follow these instructions, you will need a DiddyBorg v2, a Raspberry Pi touchscreen, a second Raspberry Pi, a second SD card with a recent version of Raspian installed, and a DiddyBorg v2 Touch Screen Kit Recent versions of Raspbian should not require extra software to run the touchscreen. For older versions you may need to update the Pi before connecting the touchscreen: sudo...

0 Comments

Written by in Build, YetiBorg - Build on

Play chase with your YetiBorg v2 Robots can make really fun pets and YetiBorg v2 is no exception. The best thing about pets is being able to play games and teach tricks, so we thought we would teach YetiBorg v2 how to follow us like a dog :) With this example you can see how we can get your robot to follow you around using only the camera. Parts...

0 Comments

Written by in Build, DiddyBorg V2 - Build on

Step 1. Open the box. If using a knife or blade, be careful not to cut deep as the Perspex parts are on top. Step 2. In the packaging are two rolled up bubble wrap bags. These contain motor mounts and hubs - don't discard them! Step 3. Lay out the parts to make sure you have everything. There should...

0 Comments

Written by in Build, YetiBorg - Build on

Step 0: Ensure you have all parts as shown above. Step 1: You should have three Perspex parts. Step 2: Remove the protective film from the Chassis. Step 3: Orient the chassis so that the spoon shaped cutout is at the bottom and the oval is to the right. Add one of the [small...

0 Comments

Written by in Build, PiBorg Tutorials on

If you wish to use a PlayStation 3 controller to control your Raspberry Pi robots then here are some details which may help. Setup for the Pi Zero W and Raspbian running Pixel If you are using a version of Raspbian which is running Pixel then you can setup the PS3 controller using the GUI. If you have a Pi 3 or Pi Zero W then you already have...

0 Comments

Written by on

Today, ModMyPi and PiBorg have announced that they are joining forces to bring a new range of high quality add-on boards and accessories to a global market. Both ModMyPi and PiBorg have been around since the early days of the Raspberry Pi Model B going on sale; ModMyPi were one of the first companies to design and manufacture injection molded cases for the Model B and have since...

0 Comments

The product is currently Out-of-Stock. Enter your email address below and we will notify you as soon as the product is available.